Aalut, am incercat sa instalez un rom original pe eten x600 dar abia dupa ce mi-a dat o eroare la instalare am vazut ca era defapt de eten x650, acum telefonul ramane la ecranul portocaliu cu logo-ul eten, am incercat sa instalez prin metoda SD card dar fara succes, tin apasate butoanele pentru a intra in bootloader dar nu vrea sa intre imi apar niste culori si liniute care se plimba pe ecran, aveti vreo idee care ar putea fi problema si cum as putea s-o rezolv?
Multumesc!
problema cu eten x600 si bootloader
719 vizualizări
4 răspunsuri
Linkuri topic "problema cu eten x600 si bootloader"
Folosiți aceste formate când vreți să faceți o referire înspre acest topic de pe forum. Click pe un câmp și copiați textul în clipboard.
Topic Link (funcționabil doar în interoriul sitului MobileWave, recomandat în caz de uz intern)
BBCode (URL pentru alte forumuri)
MW Addicted
1823 mesaje
din 24/06/2006
3 aprecieri
15 februarie 2009, 10:03:03 • actualizat 15 februarie 2009, 10:07:19 (4 ori)
cand intri in bootloader intai scoate cardul si cartela. apoi incerci iar, in principiu ar trebui sa mearga fara probleme update-ul prin SD, dar asigura-te inainte ca folosesti rom-ul care trebuie. daca nu, nu e problema, incerci prin metoda cealalta, upgrade normal. si ca idee, rom-ul de x650 trebuie sa mearga pe-al tau device 
. Si, uite un mic tutorial:
Preparations
What you will need is an SD Card, formatted in FAT. There should be nothing in the card except for the files that we are going to copy into it. Also, make sure your device is connected to the AC charger or has a full battery charge (I would recommend the former). Also, do not connect it via USB cable for charging in this case as you will soon see why.
Steps
1. Run the ROM update program on your PC and go through the installation process until your reach the ’End User Update’ window. Leave this running.
2. Go to the Temp file in your Documents. This is usually C:\Documents and Settings\username\Local Settings\Temp but it really depends on how you set up Windows.
3. Look for these 2 files, temp.dat (about 60 MB) and USBDLUpdate_Console.exe (about 4 KB) and copy them to your formatted SD Card using a card reader. You might want to copy these files to another location on your PC before copying it to your card reader if there are problems. Also, rename temp.dat to temp.bin before proceeding to the next step.
4. Put this card into your device and put the device into Bootloader mode. This can be done by pressing (and holding) the power button and voice commander key and then soft resetting. When it restarts, you can remove the stylus but keep your hold on the power and voice commander buttons.
5. The installation will proceed but at a slower rate than if you did it on your PC. This is due to the slower transfer rate between the card and device. It might take about 15-30 minutes so it would be best if your device was connected to the mains charger.
6. Installation is complete when you see this message “USB host is not connected yet“. This is your sign to do a soft reset and setup your device as the ROM installation was successful.
Possible Causes of Errors
1. If you see messages like this, “Find SDMMC Card" or “SDMMC Load Fail“, when you enter Bootloader mode, it means that the SD card is not compatible with your Eten device. In this case, make sure the device is formatted in FAT and not FAT32. If it is in FAT, try with another card, as that make of card could be the reason.
2. Use a card of capacity at least 512MB as this would allow the temp.bin to unpack the files during installation. I am not sure what is the minimum card size required but better to be safe than sorry. You could always try with a smaller card.
3. If you are unable to rename temp.dat to temp.bin, you need to enable enable another option in Windows. Select Tools and then Folder Options, select View tab and uncheck “Hide extensions for known files types" option
4. If you are still facing errors at this stage, leave a comment here and we will try to help you out
Ca si rom, as recomanda asta - Download 4shared.
. Si, uite un mic tutorial:Preparations
What you will need is an SD Card, formatted in FAT. There should be nothing in the card except for the files that we are going to copy into it. Also, make sure your device is connected to the AC charger or has a full battery charge (I would recommend the former). Also, do not connect it via USB cable for charging in this case as you will soon see why.
Steps
1. Run the ROM update program on your PC and go through the installation process until your reach the ’End User Update’ window. Leave this running.
2. Go to the Temp file in your Documents. This is usually C:\Documents and Settings\username\Local Settings\Temp but it really depends on how you set up Windows.
3. Look for these 2 files, temp.dat (about 60 MB) and USBDLUpdate_Console.exe (about 4 KB) and copy them to your formatted SD Card using a card reader. You might want to copy these files to another location on your PC before copying it to your card reader if there are problems. Also, rename temp.dat to temp.bin before proceeding to the next step.
4. Put this card into your device and put the device into Bootloader mode. This can be done by pressing (and holding) the power button and voice commander key and then soft resetting. When it restarts, you can remove the stylus but keep your hold on the power and voice commander buttons.
5. The installation will proceed but at a slower rate than if you did it on your PC. This is due to the slower transfer rate between the card and device. It might take about 15-30 minutes so it would be best if your device was connected to the mains charger.
6. Installation is complete when you see this message “USB host is not connected yet“. This is your sign to do a soft reset and setup your device as the ROM installation was successful.
Possible Causes of Errors
1. If you see messages like this, “Find SDMMC Card" or “SDMMC Load Fail“, when you enter Bootloader mode, it means that the SD card is not compatible with your Eten device. In this case, make sure the device is formatted in FAT and not FAT32. If it is in FAT, try with another card, as that make of card could be the reason.
2. Use a card of capacity at least 512MB as this would allow the temp.bin to unpack the files during installation. I am not sure what is the minimum card size required but better to be safe than sorry. You could always try with a smaller card.
3. If you are unable to rename temp.dat to temp.bin, you need to enable enable another option in Windows. Select Tools and then Folder Options, select View tab and uncheck “Hide extensions for known files types" option
4. If you are still facing errors at this stage, leave a comment here and we will try to help you out
Ca si rom, as recomanda asta - Download 4shared.
SGS2
MW Liker
51 mesaje
din 13/02/2009
16 februarie 2009, 22:37:42
Trebuia sa mearga dar se pare ca nu a mers, si nu am cum sa fac niciun update la el, pentru ca se blocheaza la imaginea portocalie cu logo-ul Eten.
Problema mea este ca nu vrea sa intre in bootloader, tin apasate tastele care trebuie si cand dau drumu imi arata un display cu multe culori si liniute, atata tot
Ma gandesc sa-l trimit la service-ul Eten, ma costa 25euro fara tva reparatia, cam mult dar macar sa mearga
Problema mea este ca nu vrea sa intre in bootloader, tin apasate tastele care trebuie si cand dau drumu imi arata un display cu multe culori si liniute, atata tot
Ma gandesc sa-l trimit la service-ul Eten, ma costa 25euro fara tva reparatia, cam mult dar macar sa mearga
MW Addicted
1823 mesaje
din 24/06/2006
3 aprecieri
18 februarie 2009, 09:24:29
atata vreme cat iti intra in logo, sigur intra si in bootloader. problema e ca nu stiu cum arata bootloader la modelul tau. insa, zimi exact cum faci (ce taste apesi, cat timp, etc) k poate ala e bootloaderu la tine.
SGS2
MW Liker
51 mesaje
din 13/02/2009
19 februarie 2009, 10:09:45
am incercat toate combinatiile posibile de taste
ex: power + voice + reset / power + camera + reset / power + reset/ power +voice +reset + end call etc etc
oricum l-am trimis la bucuresti la service, costul reparatiei e undeva la 30euro sper sa nu mai creasca
ex: power + voice + reset / power + camera + reset / power + reset/ power +voice +reset + end call etc etc
oricum l-am trimis la bucuresti la service, costul reparatiei e undeva la 30euro sper sa nu mai creasca
Înapoi la PocketPC
cine e aici?
Hei! Pentru a putea interacționa cu comunitatea Mobilewave trebuie să ai un cont (care e gratuit) și să fii autentificat.
