Downgrade nokia s60

nici asa nu reusesc ... ii dau flash apoi apare

Waiting for USB device. Press phone's power button (if you start from dead terminal)

il pornesc dar nu incepe procesul de flasuire ... ci telefonul intra in os apoi imi da eroare

Failed to open RAW USB connection
Unable to set the phone to flash mode. Unable to flash.
The flashing failed. Do you like to retry the flashing?

HRESULT 0x84012286 (-2080300410)

Flash: The device driver did not load. Verify phone is connected and powered on.

aseara era sa imi frec si eu n96 cu nes i.am dat in loc sa dau pe lupa am dat pe dracia aia verde

Chestia e ca nu trebuie sa porneasca OS-ul tot
Lasa ca am sa revin cu screenshooturi

da m-am gandit ca nu tre sa porneasca os-ul ... dar nu prea am ce sa ii fac sa nu intre in el ... plus ca in pdf-ul fasit de mine cu instructiuni zice ca pt al flasui in dead mode la managerul de conexiuni trebuie selectat no connection nu USB

Da corect, asa se face, fara conection, nu sunt acasa acum, si nu re pot ajuta 100% corect, fa cumva ca in tutorialul ala, am un prieten pe un forum strain din japonia, care a trebuit sa faca mai intai downgrate ca sa-si flashuiasca telu cu mod ASIC, avea N82 parca si a reusit

pai asa am procedat cu no connection dar tot nu am reusit ... daca afli mai multe poti sa ma ajuti si pe mine id-ul de yahoo de la profil e bun ? pot sa te adaug ... ?

Da e bun ID-ul de la profil, am sa ajut no problem
Eu am flash-uit in mod dead phone dar am facut experimente pe o vechitura de 7610
Am facut tot felul pe ala
Am scris firmavare, l-am intrerupt, si l-am scris in mod dead phone, dar chestia e ca dupa ce-am (stricat telefonul) OS-ul de pe 7610 nu mai pornea, doar se aprindea display-ul, apoi flash-uirea a mers perfect.
Dar tot nu l-am lasat asa, l-am mai intrerupt si la 75 % prin scoaterea directa a cablului in momentul cand imi arata Programing 100%
Si nu s-a stricat a pornit, dupa ce i-am facut hard reset. Tasta apel+3+steluta
Deci am sarit peste Test Mode, restore area factory si start in Normal Mode, deci flash-uirea se termina pe la 75% cand se permina Partitioning area 1 si 2 si Programing 100%. Pana aici e important.
Cand vrei sa omori un telefon intentionat nu-ti iese. Moare cand nu vrei sau nu te astepti

da asta cam asa se intampla ... ti-am dat add vb cand ne intalnim 10x

wolfy mai vii cu tutorialul ala? Am un n95 care e mort a "decedat" cand ii dadeam update...

1. First you need to download these programs, they will show up on google: OGM Development Jaf Key Emulator v4 cracked J.A.F Phoenix or Navifirm 2. Using Phoenix on Navifirm download the firmware 20.0.56 3. Install J.A.F and on the crack select step 2 on the tab, select jaf then click go. DOWNGRADE PROCESS 1 EXIT PC Suite 2. Run JAF ang go to BB5 tab... 3. Turn on the phone (if was off) 4. Connect phone to the PC in PC Suite (for S60) or general (if not mistaken, for S40) mode 5. Check Service Settings -> Read PM checkbox and hit Service button. Than enter 0 for Start and hit OK, and enter 500 for end and hit OK. When prompted to save file, save in some secure place where it cannot be damaged! 6. Remove Service Settings -> Read PM checkbox and check Service Settings -> Read PP checkbox an hit Service. Than save this file, when prompted, in the same place with PM file. 7. Now we have all possible backups for the bad case. 8. Remove Service Settings -> Read PP checkbox. And set: - Manual Flash - Factory set - Normal mode (usually already set) - CRT 308 - DOWNGRADE 9. Use check box Use Ini if you have proper firmware installed for Phoenix, this will make jaf read procuct code from your mobile phone, search the pc for installed fw and suggest you to choose one . Other way use MCU, PPM, CNT buttons to choose files manualy. (Note: MCU file must have .C0(zero)R extension, not .mcusw or .fpsx or smth) 10. Hit Flash button, JAF will ask you if files are selected properly, check twice and agree. (mine said it would kill my phone at this point, but i just contined it and it worked..) 11. WAITING....DO NOT use PC while flashing 'coz I tale NO responsibility! 12 . After you see your phone turned on all is DONE If you get your phone dead, don’t worry, just flash it with original firmware to get it alive! Also there might be need to write back your PM, use write PM checkbox and select that secure backup of PM we made am dat cu copy paste pt ca sunt la scoala nu asm timp sa il traduc

--deleted--

pai daca e "mort" cum selectezi pc suite?